Nextbase Hardwire Kit – Nextbase EU How to install a Nextbase Hardwire Kit – Nextbase EU

With the car new at Christmastime, the battery should be OK. Still, with modern cars there's not really an "off" as a some of the computers only have a 'sleep mode' and will draw a very very small amount of current when parked so starting it and letting it run awhile to charge every 2-4 weeks is a good idea. And HWK's also draw current like this, again a tiny amount but it's there. The Nextbase 522GW is a Series 2 Dash Cam that boasts an advanced image sensor and various software enhancements compared to its predecessor, the 422GW. To learn how to use the 522GW, we will first cover the installation process. The dash cam can be installed in two ways: All Nextbase dash cams come with a guide and advice on where to locate your dash cam. It shouldn’t obscure your view as a driver, or be a distraction. All of our dash cams have the option to turn off the screen when you are driving. Lead/Acid car batteries should really not be kept below 12V for any great length of time. New batteries can tolerate this longer than old ones but as a rule it is bad for the battery. Driven daily that new battery can probably tolerate 11.8V but with it drawn down to that level before the HWK cuts off and then left sitting a week it may be much lower when you try to start the car so better to use a setting of 12V or higher for the HWK. Panasonic TX-65FZ802B - Panasonic DP-UB420EBK 4K Ultra HD Blu-ray Player Logitech Harmony Ultimate + HUBThe Hard Wire Kit will allow the camera to draw nominal current from the car's battery, preventing the cam's battery from being drained. The Hard Wire Kit has an in-built voltage cut off which protects the car's battery from being drained below 11.2V. We'd recommend using a Permanent Live fuse with Parking Mode enabled. This voltage cut off is not currently adjustable from 11.2V. G Sensor / File Protection (In the event of an impact the device will automatically 'protect' the recording, stopping the file from being over-written).

Nextbase 522GW | Page 3 | AVForums Nextbase 522GW | Page 3 | AVForums

Once you’ve confirmed the length, we can start with placing the suction cup on the windscreen, ideally just behind the rearview mirror on the passenger side.

I bought the car one year ago and the battery is fine, also I don't think the camera software is supposed to freeze and heat up the camera. The camera was apparently running for almost 3 days instead of entering parking mode, so my battery didn't have enough power left to start the car. I am on the latest firmware and have tried stuff like reformatting the SD card etc.. Yet the dash cam is freezing at random. Why is it doing this? I shouldn’t have to worry about my dash cam randomly stopping recording as it has frozen. Camera Requirement: Dash Cam compatible U3 SD card. We recommend the Nextbase 64GB U3 Micro SD Card. Nextbase SD cards are specifically manufactured and designed for Nextbase Dash-Cams ensuring high quality video footage, reliability and endurance.

522GW – Nextbase Parts 522GW – Nextbase Parts

a>

Connecting your 522GW to your Apple device using the MyNextbase Connect app

If fitted to a permanent live supply, the inbuilt minimum voltage limiter will protect the vehicle's battery from going flat. With the Hardwire Kit installed on a switched live supply, the Dash Cam will power on and start recording automatically when the vehicle is opened or starts. Ah, good to know, wish I was aware of that before buying their cam. I will pay attention to that whenever this one dies on me and I need to buy a new one! Ben Wells is a tech enthusiast specializing in cameras and GPS devices. He has a keen interest in reviewing dashcams, navigators, and other useful car... There are two options to installing a dash cam, the easiest is the 12v cigarette lighter dash cam installation, but the neatest is using a hardwire kit. Go into Settings (the settings icon will show in the top left of the screen once a recording is stopped)

Hardwire Kits) Do Dashcams Drain Your Car Battery? (+ Best Hardwire Kits)

I don't know if the NB HWK is adjustable or how it's done but I'd look into that. Some HWK's aren't adjustable and are set too low (11.8V is common, some are 11.6V or lower ) and there's some manufacturing tolerance so it may be ~0.1V or so lower than the setting. It could also be you've got a faulty HWK but they rarely fail in this manner. You need a voltmeter to diagnose this but you can look for an adjustment and set it to 12V or a bit higher and that may take care of things. The Nextbase 522GW Dash Cam offers stunning 1440p HD resolution for crystal clear video recordings. The 522GW is fitted with an inbuilt polarising filter to dramatically reduce windscreen glare and reflection to produce enhanced recordings. It uses a vastly upgraded 3" HD IPS touch screen for easy menu selection and a host of new and exciting features. They are also still using lipo batteries in their cameras which gives the cameras a typical 1 year lifespan when all the decent camera manufacturers have switched to super capacitors which last so long that nobody yet knows how many years! The GPS has been improved dramatically too - connecting now 10 times a second for faster and more accurate location finding. I hardwired the camera using the Nextbase hardwire kit, it worked great for a 30 mins or so and then the camera shut off due to low battery. The blue LED isn’t turning on.

If you don’t want a dashcam to draw from your battery when the car is off, this can easily be achieved by hard wiring the camera through a fuse that turns off with the engine. However, the downside of this is that you won’t be able to use parking mode which is a key feature of most devices. An important and new feature is the use of Alexa to give you voice control over some of the actions. Does a dashcam drain your car battery? If a dashcam is hard wired to your battery, it will usually be connected so that it can continue drawing power when the car is off, this could drain your battery if the right pre-cautions are taken. However, any good hardwire kit will have a built-in voltage meter which cuts out when the battery reaches a critical point. We must measure the included 4m cable, which should be sufficient to reach the windscreen mounting location.