So before you think about replacing your clubs, first examine each club and then separate them in 2 piles. Dedicate a good amount of time while using sandpaper on your driver head. Good preparation time will pay off in the long run. When removing excess paint. Wrap a cleaning swab soaked in acetate around a razor blade or any flat straight object. Rapidly wipe the swab over the area. Replace with a cleanly soaked swab if dirty. Repeat these steps until the club surface is completely clean. Do not use Q-tips as they can cause an indentation on the surface of the paint. First, you need to ensure you use the right kind of paint. We’ve seen/heard people use all sorts of paints and fills ranging from nail polish to permanent markers and paint pens, but we’ve had the most success using hobby/model paint. Typically, enamel hobby paint is more durable, but we’ve found acrylic hobby paint to be easier to use and easier to dilute (which is important).

Allow the paint to dry ( 30 TO 40 minutes) Use sandpaper to ensure a smooth, shiny surface, repeat the process at least 4 times. Place the shaft on a piece of newspaper or a drop cloth that is lengthier and wider than the shaft. To ensure that your putter is free of paint, grease, and debris, use a toothbrush dipped in dish washing soap and make sure you clean it.Take a metal bowl and pour acetone into it. Wear gloves made of latex as a precaution before you transfer the acetone. When looking for suitable paint to repair chips, scratches or, scuff marks, it is essential to choose a paint that will withstand the heavy impacts that all golf clubs will encounter. Acrylic paints, on the other hand, are not designed to endure the friction that the club is subjected to on the golf course.

Some preparation is required before it’s time to paint your golf clubs. There are two vital aspects that need to be taken care of before any painting can begin: Use a pointed object like a needle or a safety pin to clean out inaccessible areas in the golf iron. Irrespective of what purpose you are using the paint for, there are several steps that have to be followed before applying the paint. Materials Required Use a Q-tip to apply generous amounts of paint-remover to the areas of the golf club where you do not want any old paint. Acetone will work well. Wear latex gloves before using acetone.Cover the other parts. The club head and the golf club grip may be covered with painter’s tape so that paint does not get on them. Once the paint has been applied to the required area using your preferred method, allow the paint to dry With all three methods it will be necessary to smooth out and remove excess paint and clean up any spillage onto the clubs ensuring that the paint remains only in the area you want to fill. So please continue reading as I will outline all the steps that show you exactly how to paint your golf clubs and get them looking new again! If there are areas that you would not want to be painted, use masking tape or painter’s tape to cover these areas.

As with painting the whole club, the same initial prepping must be followed ensuring that all paint is removed from the areas to be painted. Once cleaning is satisfactorily completed and areas to be painted are dry Custom Paint Fill can commence. The process can be repeated 2 or 3 times to create a deep glossy color. Allow the paint to dry and mature for at least 24 hours before using the clubs. It is easy to apply with a small needlepoint applicator providing accurate results. The paint, touch dries within 30 minutes and is fully dry within 6 hours. It is suggested that only one coat is required. If you feel that the color is not intense enough, add 1 or 2 more coats. Once it has soaked-in the paint remover, use a nail, or any object with a pointed edge to scrape the paint from the golf club and out of narrow or hard-to-reach areas, like letters and edges. The reasons for the painting of golf clubs can be to repair chips on a driver, paint the complete shaft or, Custom paint fill.Paint Remover. Acetone can be used. Make sure that strong latex gloves are worn to protect your hands.

Let the existing paint on the putter soak up the acetone. Allow it to sit for a good length of time. To remove any excess paint, use a razor blade. You can also use a lint-free piece of cloth dipped in nail polish remover to remove the excess paint. Making sure you are wearing latex gloves use a sharp metallic object to scrape the old paint off the club heads. Use a nail to remove paint from the letters, edges and, difficult-to-reach places.

available in our online store!

Apply generous amounts of paint-remover using Q-tip. Acetone will also do the job. Wear latex gloves before using acetone. Enamel Paint. Enamel paint and preferably epoxy-based enamel paint is highly recommended. Enamel is oil-based, adheres easily to metal surfaces, is highly durable, and, has a gloss finish. Two-Part Urethane Automotive Coating. Many regard this as a good product for painting golf clubs, for its high gloss finish and durability. Is more expensive and because it is spayed on is not economical for Custom Paint Fill Applications.