Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.

If the surface absorbs the Polytrol unevenly (i.e. some matte and some shiny patches) move any surplus oil from shiny areas to matte areas.Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint free cloth. Leave it to dry. Although we didn’t have any mildew on the door, if you do, don’t worry. Mildew can be treated with a 50:50 bleach and water solution. Just scrub it on, leave it for 10-15 minutes, then rinse it off. It is natural for time and exposure to erode the appearance of a gelcoat. However, by restoring it, you are not only making your boat more pleasing to the eye, but you are making it last longer. Once you have finished using Polytrol, clean any brushes or other tools you may have used with white spirit. Cloths can be left flat to airdry before discarding.

Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry. Applying Polytrol to metal When someone arrives at your home, your front door is one of the first things that they’ll see. A tired, faded front door can make even the most beautiful of homes seem a little neglected. Gelcoat Restorer is simple and easy to apply and can be done in five short steps, some of which you can often omit depending on the state of your gelcoat to begin with:This customer has used Owatrol’s Polytrol to revive the plastic trims on their car and to great effect. These small details can really make the difference between your car looking old and tired, or a great asset. Do not allow excess Marine Polytrol to dry and create a film on the surface (always remove excess product). If you have prepped the surface and applied the Polytrol correctly but see next to no improvement, unfortunately, the pigments may just be too damaged to restore. If the surface treated has been exposed to many years of harsh UV rays and weathering, there is a chance that even Polytrol cannot restore it. When do I need to re-apply Polytrol? Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water filled metal container, before disposing of them with household waste. Rags may be laid flat and air dried before

For a shinier finish, buff the surface with a lint-free polishing cloth. Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.

3. Clean up

Note: Marine Polytrol is not a surface coating. Its place is in the surface, not on top. Maintenance With Gelcoat Restorer, maintenance is easy. The results are long-lasting but when you see they are fading, simply repeat the easy process again. Deep penetrating oil that restores the original look and finish to gelcoat, plastic, metal and other surfaces Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).

Apply Polytrol using fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry. Have tried numerous products over time without success until i came across this particular car bumper and trim restorer product. Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 12 hours depending on surface. When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry. Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc. Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fiberglass (GRP). Marine Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake. Ideal Uses for Marine Polytrol Gelcoat Restorer

Can I use Polytrol on white surfaces?

However, surfaces exposed to high UV and weathering (such as by the sea) will require it more often, whereas surfaces that do not have this type of extreme exposure won’t require another application for potentially 24+ months. Where can I buy Polytrol from? After cleaning, leave the door to dry for 24 hours before applying Polytrol. Make sure that your door is completely dry before moving on to the next step! 2. Apply the Polytrol