Like the above series, also surface mount only however featuring positive latching mechanism and a completely different type of mating surface. VH (3.96mm pitch)

JST manufactures a large number of series (families) of connectors. [2] The PCB (wire-to-board) connectors are available in top (vertical) or side (horizontal) entry, and through-hole or surface-mount. A teeny weeny surface mount only connector family from JST. Commonly found inside laptops for connecting various items to the motherboard. Housings are available with “wings” to aid disconnection. Housings are “SH” and headers are “SR”. Example part numbers Choosing the Right JST Connector". DronesEtc. Archived from the original on 4 March 2016 . Retrieved 13 August 2015. EH is a 2.5mm pitch connector deployed in low cost products where a current carrying connector is needed, but PCB real-estate is highly constrained. They are significantly slimmer than XH connectors. Example part numbers A female JST PH has one slot (or rather a cut-out) going down in the middle of the female. Which corresponds to the bar going down the middle of the male (as can be seen on your photo). Either side of the slot/cut-out are two small holes at the bottom.The JST-PH connector is used on many high current micro ESC and LiPo batteries - e.g. the E-flite Blade mCPX helicopter, the Spektrum AR6400LBL receiver and several Parkzone, E-Flite 'UMX' models. This is a thin, low-profile 2.0mm pitch connector 8.0mm in height after mounting and 4.5mm in width. See the top left female connector in this photo from Common JST Connector Types - PH (2.0mm pitch): It is designed to meet the demand for high-density connection of internal wires to printed circuit boards. It is compact, highly reliable and low in cost. Among our electric components, we can put forward a wide variety of innovative catalog products and crimping tools: FFC/FPC connectors (insertion strength zero, no ZIF), to crimp/crossing, SMT/CMS

surface mounting), insulation displacement (IDC), board to board, board to wire, wire to wire, LED, waterproof, pitch from 0.1 to 13mm, hand tools, semi-automatic presses and applicators for all our

Spécifications

The solder side of the header has a retention mechanism that prevents it from floating during soldering. As a result, the header can be positioned accurately. a b "List of JST connector series; JST". Archived from the original on 2020-11-12 . Retrieved 2013-08-31. The fully shrouded header has walls on all four sides to prevent improper connection to the mating housing and to prevent the intrusion of flux and other contaminants. I don’t use these very much but one advantage of them is height. The mated assembly is considerably slimmer than any other type of connector I use. It’s a shame the pitch isn’t 2.54mm – I would use them a lot more otherwise. That said, you can usually jam 2 or 3 (maybe even 4) position headers onto strip board if needed. Example part numbers Your male connector also has two small lumps/keys then correspond to the two small holes either side of the long slot on the female.

JST Connector” is either shorthand for a connector manufacturer called Japan Solderless Terminal, or a vernacular term for a range of different type of wire to board connectors, which either are, or resemble designs from Japan Solderless Terminal. IWISS IWS-2820M. A copy of the Engineer PAD-11. Not as well made but for the significantly lower price, it could be forgiven. This 2.0mm pitch connector is very commonly seen in low cost consumer electronics as well as a plenitude of pre-fabricated hobbyist PCBs and parts. They’re dirt cheap, reasonably compact but not particularly robust.This connector is also available in a surface mount configuration. Its housing is made of heat resistant resin so that it is not adversely affected during reflow soldering. Because of its tiny size and ability to be surface mounted, this connector meets the demand for high-density mounting of components inside electronic products. JST-SH | Molex Picoblade (1.25mm) | JST-ZH | Molex 2mm | JST-RCY | 1.27mm | AR6400/PKZ3352 | DC | Power The female PH has a wide cut out and two holes at the bottom (2 mm pin spacing), whereas the XH has two slots from the top towards the bottom (2.5 mm pin spacing). We recommend you own a set of crimping pliers as well, such as these nice ones from Engineer - they're easier to use than trying to crimp with pliers.

department. This allows us to be closer from our French customers and main European decision-makers. JST connectors are electrical connectors manufactured to the design standards originally developed by J.S.T. Mfg. Co. (Japan Solderless Terminal). [1] JST manufactures numerous series (families) and pitches (pin-to-pin distance) of connectors. [2] [3]

Connector Types

For more obscure types, no hand tool is offered, however JST do sell a hand frame (YRS-XXX) for mounting dies for their MKS-L applicator (used in the AP-K2N crimping machine), a very expensive solution, and the only option for production/mission critical applications. Unofficial / Generic