PINECIL – Smart Mini Portable Soldering Iron, New Version 2

Product Information

Easy way: just get a Power Wheels adapter. They are made for different tool brands and get a DC5525 Pigtail wire.

Home - PINE64 EU

If the GaN charger senses a potentially dangerous condition, i.e., overcurrent spikes, the chips are designed to go into a cycle-by-cycle sleep state, protecting the device. Over current protection in GAN.Get a Power Wheels Adapter like this for Ryobi, then splice/connect it to a DC5525 Pigtail to complete connection to Pinecil. If you are truly “in the field” with no access to an outlet, you can power Pinecil V2 from a USB C powerbank, as long as it can produce the necessary voltage. You can also use LiPo batteries in 3 / 4 or 5S configurations, or in a pinch an 18-20V Lithium Ion tool battery can be used. Recommend operating voltage 12-21V, some components can tolerate higher voltages at "absolute maximum" but it's very ill-advised Miniware’s previous soldering irons, the TS100 and TS80 used just a single power connector, respectively DC 5525 and USB-C. With the TS101 we see both as available power sources. But which one is better? In such cases, some developers decide to maintain a fork of InfiniTime with their changes. A fork is basically a copy of the project that they maintain on their own. To this day, InfiniTime counts 584 forks! Among these forks, you’ll find Sec42‘s fork that adds changes to make notifications easier to read by “old” eyes and Dmlls‘s fork which adds the Infineat watchface and is very well maintained. These forks are a good thing as they allow developers to make their contributions available to the public even if they cannot be merged in InfiniTime right now, and they provide more choice to the users. Everyone wins!

Pinecil | PINE64

Protocol Droid bot: the live chat is bridged to Discord, Telegram, Matrix and IRC. Those bridges will not have all the features available within all platforms, but the chat is relayed between all four by a bot named "Protocol Droid".QC3.0 phone chargers: not recommended, it is weaker in power and does not auto-negotiate like USB-C PD does. QC3 requires manually setting the voltage in the Power settings. A minimum of 3 amps is needed and many QC phone chargers are only able to provide a low 12V 1.5amp, limiting Pinecil to about 17W of thermal capability which is weak and slow. It may not even start to heat, but if it does, it may get repeated Thermal Runaway message (this means the weak power causes Pinecil to auto-shutdown continuously). Note: do not connect the DC barrel at the same time as a USB-C cable. Pinecil was designed to only have one cable plugged in at a time. You could damage/break the PC and Pinecil doing this.

Pinecil - PINE64 Pinecil - PINE64

I choose Pinecil because it has 3 ways to power on USB-C PD65w 20V, DC barrel up to 24V/3amps+, and DC barrel with any of my tool batteries (18V-21). the older V1 supports up to 21V (but 24 if you do a modification).

Brand

Zendure Power bank like this one does not work. It does not appear to be USB-C PD 3.0 compliant. Only the USB-A port seems to work at lower QC voltage. It does not deliver USB-C 20V-5amps or USB-C 20V -3amps. Note: Bluetooth (BLE) apps require upgrading Pinecil V2 to IronOS 2.21 or newer firmware here. Power Supplies and Watts The detailed display option shows power draw, current temperature, supply voltage, and time until sleep mode starts.

Pinecil V2 soldering iron gets BL706 Bluetooth LE RISC-V MCU Pinecil V2 soldering iron gets BL706 Bluetooth LE RISC-V MCU

Notebook AC Adapter LITEON PA-1700-02 ([email protected], 65W) (tip is 1.7mmx5.5mm would need adapter for DC5525)Wait a few seconds for the regular display to return, then hold down [-] for a moment to turn the heat off. Except in this device it actually brings some interesting features on the table, all that on open and relatively simple hardware, offline and feature oriented, which is important.